Hamlet HDSL8K2

[alexo]

Hello guys,

I own a Hamlet HDSL8K2 usb ADSL modem.

After successfully installing EciAdsl drivers for my Ubuntu 8.10 distro and probing my modem I get the Vid1, Pid1, Vid2, Pid2 values.
Checking for these values on the supported modem list I get a perfect matching with the two following models:

Conitech Kinowa
D-Link DSL200 generation III

.bin file GS7470 synch20

The modem successfully get synched but the message I get immediatly after the connection attempt is:

modem hangup

what should I do tho avoid that?

Tank you in advance

[alexo]

Here is the log of a connection attempt:

[EciAdsl 1/5] Setting up USB support...

Preliminary USB device filesystem is OK

[EciAdsl 2/5] Uploading firmware...

Process skipped .. no more needed
firmware loaded successfully

[EciAdsl 3/5] Synchronization...

OK eciadsl-synch: success
Synchronization successful

[EciAdsl 4/5] Connecting to provider...

using channel 13
Using interface ppp0
Connect: ppp0 <--> /dev/pts/4
sent [LCP ConfReq id=0x1 <magic 0x38a85c22>]
Script /usr/bin/eciadsl-pppoeci -vpi 8 -vci 35 -vendor 0x0915 -product 0x8104 -mode VCM_RFC2364 finished (pid 22036), status = 0x0
Modem hangup
Connection terminated.
using channel 14
Using interface ppp0
Connect: ppp0 <--> /dev/pts/4
sent [LCP ConfReq id=0x2 <magic 0x15c3e2a2>]
sent [LCP ConfReq id=0x2 <magic 0x15c3e2a2>]
sent [LCP ConfReq id=0x2 <magic 0x15c3e2a2>]
sent [LCP ConfReq id=0x2 <magic 0x15c3e2a2>]
sent [LCP ConfReq id=0x2 <magic 0x15c3e2a2>]
rcvd [LCP ConfAck id=0x2 <magic 0x15c3e2a2>]
rcvd [LCP ConfReq id=0x35 <mru 9178> <auth pap> <magic 0x5517445d>]
sent [LCP ConfAck id=0x35 <mru 9178> <auth pap> <magic 0x5517445d>]
sent [PAP AuthReq id=0x1 user="rinogoffredo" password=<hidden>]
rcvd [PAP AuthAck id=0x1 ""]
PAP authentication succeeded
sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
rcvd [IPCP ConfNak id=0x1 <addr 151.56.155.173> <ms-dns1 193.70.152.15> <ms-dns3 193.70.152.25>]
sent [IPCP ConfReq id=0x2 <addr 151.56.155.173> <ms-dns1 193.70.152.15> <ms-dns3 193.70.152.25>]
rcvd [IPCP ConfAck id=0x2 <addr 151.56.155.173> <ms-dns1 193.70.152.15> <ms-dns3 193.70.152.25>]
rcvd [IPCP ConfReq id=0xc8 <addr 151.6.158.72>]
sent [IPCP ConfAck id=0xc8 <addr 151.6.158.72>]
local IP address 151.56.155.173
remote IP address 151.6.158.72
primary DNS address 193.70.152.15
secondary DNS address 193.70.152.25
Connection successful

[EciAdsl 5/5] Setting up route table...

Waiting for ppp0...
Adding default route... SIOCADDRT: File exists
failed to set default route to ppp0

[alexo]

After many attempts, I finally got it working.

What I did was to modify
/etc/eciadsl/eciadsl.conf file as follow:

Code: Select all

VID1=0915
PID1=8104
VID2=0915
PID2=8104
MODE=VCM_RFC2364
VCI=35
VPI=8
FIRMWARE=/etc/eciadsl/firmware00.bin
SYNCH=/etc/eciadsl/gs7470_synch20.bin
PPPD_USER=your_username_goes_here
PPPD_PASSWD=
USE_DHCP=yes
USE_STATICIP=no
STATICIP=
GATEWAY=
MODEM=D-Link DSL200 generation III
MODEM_CHIPSET=GS7470
SYNCH_ALTIFACE=0
PPPOECI_ALTIFACE=0
PROVIDER=IT..Infostrada
DNS1=193.70.192.25
DNS2=193.70.152.25


Thank you to the Eciadsl developers for their work.

[FlashCode]

Hi Alessandro,

Thanks for your report, I'll add it soon to driver and website (modems page).

[FlashCode]

Done.