[EciAdsl 4/5] Connecting to provider...

[hebus]

Bonjour,

Je n'arrive pas à passer l'étape 4/5 connecting to provider. Il me semble pourtant que l'authentification auprès de mon fournisseur s'effectue correctement, mais je ne comprends pas les lignes qui apparaissent après CHAP authentication succeeded.

Mon fournisseur m'a transmis ses DNS (que j'ai saisis) et le mode de connection (LLC / PPPoE).
J'ai également installé rp-pppoe.

Modem D-Link DSL 200 USB, Ubuntu Hardy

PS : je débute sous Linux...

Merci d'avance pour votre aide


Voici ce que donne la commande eciadsl-start :

[EciAdsl 1/5] Setting up USB support...

Preliminary USB device filesystem is OK

[EciAdsl 2/5] Uploading firmware...

GlobeSpan GS7070 USB ADSL WAN Modem compatible modem found (in 2250ms)
eciadsl-firmware: success
firmware loaded successfully

[EciAdsl 3/5] Synchronization...

OK eciadsl-synch: success
Synchronization successful

[EciAdsl 4/5] Connecting to provider...

using channel 4
Using interface ppp0
Connect: ppp0 <--> /dev/pts/1
sent [LCP ConfReq id=0x1 <magic 0xf5fe899b>]
rcvd [LCP ConfReq id=0x35 <auth chap MD5> <magic 0x1125bf8e>]
sent [LCP ConfAck id=0x35 <auth chap MD5> <magic 0x1125bf8e>]
sent [LCP ConfReq id=0x1 <magic 0xf5fe899b>]
rcvd [LCP ConfAck id=0x1 <magic 0xf5fe899b>]
rcvd [CHAP Challenge id=0xe5 <52daa7339a7fa569a6742a875c0f31bb>, name = "ipc-fri670-r-br-01"]
sent [CHAP Response id=0xe5 <a3c1f567e56c2097d8ff90522f4e6c71>, name = "XXXXXXX@bluewin.ch"]
rcvd [CHAP Success id=0xe5 ""]
CHAP authentication succeeded
CHAP authentication succeeded
sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
rcvd [IPCP ConfReq id=0x1 <addr 83.79.144.1>]
sent [IPCP ConfAck id=0x1 <addr 83.79.144.1>]
rcvd [LCP EchoReq id=0x1 magic=0x1125bf8e f5 fe 89 9b]
sent [LCP EchoRep id=0x1 magic=0xf5fe899b f5 fe 89 9b]
rcvd [IPCP ConfReq id=0x2 <addr 83.79.144.1>]
sent [IPCP ConfAck id=0x2 <addr 83.79.144.1>]
sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
rcvd [IPCP ConfReq id=0x3 <addr 83.79.144.1>]
sent [IPCP ConfAck id=0x3 <addr 83.79.144.1>]
sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
rcvd [IPCP ConfReq id=0x4 <addr 83.79.144.1>]
sent [IPCP ConfAck id=0x4 <addr 83.79.144.1>]
rcvd [LCP EchoReq id=0x2 magic=0x1125bf8e f5 fe 89 9b]
sent [LCP EchoRep id=0x2 magic=0xf5fe899b f5 fe 89 9b]
rcvd [IPCP ConfReq id=0x5 <addr 83.79.144.1>]
sent [IPCP ConfAck id=0x5 <addr 83.79.144.1>]
sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
rcvd [IPCP ConfReq id=0x6 <addr 83.79.144.1>]
sent [IPCP ConfAck id=0x6 <addr 83.79.144.1>]
sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
rcvd [IPCP ConfReq id=0x7 <addr 83.79.144.1>]
sent [IPCP ConfAck id=0x7 <addr 83.79.144.1>]
rcvd [LCP EchoReq id=0x3 magic=0x1125bf8e f5 fe 89 9b]
sent [LCP EchoRep id=0x3 magic=0xf5fe899b f5 fe 89 9b]
rcvd [IPCP ConfReq id=0x8 <addr 83.79.144.1>]
sent [IPCP ConfAck id=0x8 <addr 83.79.144.1>]
sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
rcvd [IPCP ConfReq id=0x9 <addr 83.79.144.1>]
sent [IPCP ConfAck id=0x9 <addr 83.79.144.1>]
sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
rcvd [IPCP ConfReq id=0xa <addr 83.79.144.1>]
sent [IPCP ConfAck id=0xa <addr 83.79.144.1>]
rcvd [LCP EchoReq id=0x4 magic=0x1125bf8e f5 fe 89 9b]
sent [LCP EchoRep id=0x4 magic=0xf5fe899b f5 fe 89 9b]
sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
rcvd [LCP EchoReq id=0x5 magic=0x1125bf8e f5 fe 89 9b]
sent [LCP EchoRep id=0x5 magic=0xf5fe899b f5 fe 89 9b]
sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
IPCP: timeout sending Config-Requests
sent [LCP TermReq id=0x2 "No network protocols running"]
rcvd [LCP EchoReq id=0x6 magic=0x1125bf8e f5 fe 89 9b]
Terminating on signal 2
Child process /usr/bin/eciadsl-pppoeci -vpi 8 -vci 35 -vendor 0x0915 -product 0x8000 -mode LLC_RFC2364 (pid 5532) terminated with signal 2
Modem hangup
Connection terminated.
ERROR: failed to connect

Après la ligne indiquant "No network protocols running" je dois faire un CTRL+C sinon mon système se bloque complètement.

[FlashCode]

Je pense qu'il faut simplement essayer d'autres fichiers .bin de synchro. Certains donnent lieu à une connexion instable.